Artificial Turf Thousand Oaks – Everything That Some Others Say..

After you have completed the preparation stage which includes measuring just how much artificial grass you require, installing appropriate drainage (if needed) and removing the natural grass layer, you will be ready to install your artificial grass lawn. This post outlines the steps you ought to follow to assist you to do the job right, from laying the base, connecting joints and preventing weed growth.

Lay Gravel Base then Sharp Sand – If neccessary, use treated timber/timber stakes to put in an area frame. We recommend 4 X 2 inches of tantalised treated timber for heavy clay soil areas and poorly draining areas and two X 2 inches of tantalised timber for good draining areas. Screw these timbers to the stakes leaving the stakes on the within the perimeter. Should the Artificial Grass meet a concrete path, wall or decking, position the timber flush with all the surface height and also by using 10mm temporary fillet, pack the timber near the wall leaving the area to enable you to tuck the Artificial Grass between the timber and the adjoining material at a later stage.

Position the stakes from the inner perimeter timber edging and hammer into the ground ensuring the stakes are slightly less than the timber edging. Next screw the timber stake to the timber edging. With heavy clay soils we recommend laying a crushed stone surface of up to 3 inches. This will never be necessary for the majority of areas and just required if you have a high water table where the ground holds water for a long period of your time after it rains. Next compact the floor employing a vibrating plate that can be hired from an equipment hire company. Make sure the perimeter is compacted and below the timber edging by 1 inch. Infill the perimeter with sharp sand and level employing a rake. Make sure the sand is level to the peak of the timber edging and compact again.

For good drainage areas spread a layer of sharp sand to blind over the soil. Next compact the floor using a vibrating plate which can be hired from an equipment hire company. Make sure the perimeter is compacted and level with the timber edging. Should you put more work in at this point, your Artificial Grass Lawn will appear better consequently.

Weed Control Layer – Apply the weed control geo textile membrane and cut as necessary. Tack using small 1 inch galvanised clout nails to the timber edging. This weed control geo textile membrane prevents any possibility of weed growth through the artificial grass drainage holes.

Roll out Artificial Grass – Lay the Artificial Grass in the desired direction working on the carpet and not on the levelled base. Ensure the carpet is positioned to minimise cuts, joints and waste overlaying the timber edging by no less than 4 inches. When the artificial grass meets a path or edge, and for those who have laid the timber edging correctly as previously described, then this artificial grass can be wedged between. If joining, please ensure that the artificial turf cost thousand oaks is laid with all the pile running inside the same direction on every piece. Lay the carpet on the top of the sand rather than dragging it across the base material. To aid stop wrinkles or creasing it is advisable to allow 2 to 3 hours to settle before continuing with jointing and adhesive. Cut grass to shape using a sharp Dolphin or Stanley knife or scissors.

Jointing – When jointing your outdoor carpet together, ensure the pile runs inside the same direction. Shut down manufacturer’s edge strip (if present) and butt two edges together ensuring you will find no gaps more than 1mm in between the two carpet edges. The accuracy with this determines how visible the join is following the completion. Fold back edges and position jointing tape (smooth side down) so the edges from the carpet fulfill the tape when joined.

Adhesive – a) Apply the cartridge adhesive in a zig zag motion on the rougher side in the tape allowing one cartridge for every 3 linear metres. Turn down carpet and press both edges in to the wet adhesive, ensuring every piece marries up and it has no overlap. When you are carrying this out with your fingers, mix the fibres together to conceal the join. When the whole length is within place and you are pleased with its appearance it is essential to walk across the join many times to activate the glue and bond the grass towards the tape. Weigh down the seam to ensure good exposure to the glue until it cures. The more care taken using the operation the neater and tidier the joint will likely be.

b) If making use of the 2-component multi-purpose adhesive, ensure thorough mixing of these two components before use. Apply adhesive to the rough side of the tape and spread evenly across a width of a minimum of 20cm using if possible a notched trowel. Sufficient adhesive should be applied in order that when the artificial grass carpet is pressed in to the adhesive, a transfer within the xggnvo backing is done. Turn down carpet and press both edges in to the wet adhesive, ensuring every piece marries up and it has no overlap. Make sure the carpet does not crest at the seam and is also holding flat on the bonded area. When the whole length is at place and also you are satisfied featuring its appearance it is actually required to walk along the join many times to activate the glue and bond the grass towards the tape. Weight the seam to make certain good connection with the glue until it cures. The better care taken with the operation the neater and tidier the joint will be.

When you should endeavour not to put adhesive on the carpet small amounts of glue are easy to remove from your artificial grass fibre using White Spirit as well as a small off cut of the artificial grass. Small amounts of cured glue usually can be removed. To avert this situation and the possibility of injury to the artificial grass, care and precautions needs to be delivered to avoid contact with the fibres all the time. Once the artificial grass has been jointed and glued and you also are pleased with the levels screw the grass to the timber perimeter framework using galvanised screws at least of 12 inch intervals.

Spread Sand (Optional, based on Grass Selected) – If the artificial grass continues to be laid use silica sand, which is kiln dried and brush into carpet along the way. Each product might have sand infill but this is only utilized to stabilise the carpet as well as at almost no time in case the sand be visible. You have to obtain an even spread within the surface employing a brush to develop the depth in layers. Usually do not apply the sand in a single application. Brush sand into pile right after laying as the artificial grass is dry and even though weather is good. Brush vigorously from the fibres in the carpet pile to let the tufts to stand upright. Putting the correct quantity of sand in helps hold the artificial grass to bed down, protects the fibres and in addition keeps them standing allow it the look of real grass.